#Clover efi autoconfig install#
#Clover efi autoconfig drivers#
#Clover efi autoconfig update#
#Clover efi autoconfig download#

If you have an unsupported SATA controller (8086:a103, 8086:9d03), use SSATA-unsupported.kext.This can fix no drives detected at Disk Utility. If your SATA uses RAID mode instead of AHCI mode, you'll need to use an injector.You do not need these kexts for booting the installer. The VirtualSMC package includes Battery and Sensors plugins (SMCBatteryManager.kext, SMCDellSensors.kext, SMCLightSensor.kext, SMCProcessor.kext, and SMCSuperIO.kext).

#Clover efi autoconfig install#

You can install the rest required kexts at the time of post-installation.

Only use basic kexts which is required to boot off the installer.

Navigate to /EFI/CLOVER/kexts/Others/ and place all the 5 kexts (Lilu.kext, VirtualSMC.kext, WhateverGreen.kext, USBInjectAll.kext, and VoodPS2Controller.kext)

Use the kext from RELEASE folder and RELEASE.zip file.Р”В¬opy all the kexts from the release folder downloaded above.

#Clover efi autoconfig download#

Download the latest version for better support.

The pre-built binaries/downloads are available in the README.md section. Remove all the folders, 10.x, except ' Other'. Follow the guide below to place the necessary kexts. In order to boot into the installation, you need to place the necessary kexts. After installing the Clover bootloader, the EFI partition should be mounted on your Desktop.

#Clover efi autoconfig drivers#

Now youРІР‚в„ўve successfully installed clover and the required drivers on your USB.

Without HFSPlus, you won't be able to see any HFS+ volumes including your installation drive.Р”РЃ.Copy the additional drivers to: /EFI/Clover/drivers64UEFI.

The clover bootloader will be installed to your installation drive. Confirm the above options and click on Install. The rest necessary drivers will be installed automatically by default.Р”В¦.

Drivers64UEFI: OsxAptioFixDrv-64 or AptioMemory Fix and ApfsDriverLoader-64.

Configure the following options for UEFI. If youРІР‚в„ўre using a UEFI based laptop, then itРІР‚в„ўs recommended to install Clover as a UEFI. Click on Customize and configure the following settings. Simply click on Change Install Location and select your installation Drive i.e Install macOS High Sierra.Р”Тђ. By default, the Clover Bootloader will select the system drive i.e Macintosh HD. Extract the Clover EFI bootloader installer package and right click on the. According to your laptop, either Legacy or UEFI, install the Clover Bootloader.Р”Р€. For High Sierra and later, 16GB is recommended.Р”Сћ. In order to boot the laptop using the USB, follow the steps below. Sudo '/Applications/Install macOS Sierra.app/Contents/Resources/createinstallmedia' -volume /Volumes/USB -applicationpath '/Applications/Install macOS Sierra.app' -nointeractionР”Р„t this point, the bootable USB can be only used to boot Mac only. To create the installation USB, createinstallmedia method is recommended and is only valid method to prepare the installer. The next step is to create a bootable installation drive. Also when seeking for support, the hardware details should be present in your profile.Р”В¬reating a Bootable USB Flash Drive with Createinstallmedia Starting your journey without knowing your hardware will make your journey difficult with no any chance of success.

If you're having a laptop which doesn't have UEFI capabilities, then follow the Legacy guide.Р”В«efore you start, get to know about your hardware. If you're having a laptop which is UEFI capable, follow the UEFI guide.

#Clover efi autoconfig update#

Those who are not using Clover, can update their configuration for clover and continue to use it.Р”В¬lover is one of the most advanced bootloader yet and it can boot upto almost any OS. This guide covers a complete step to boot the macOS installer on your Laptop using Clover bootloader. Booting macOS installer on laptops can be a challenge for the new users.